Most electrical problems get poked at before anyone calls. A tripped breaker gets reset. A dead outlet gets tested with something plugged into it. A flickering light gets a new bulb. That is sensible, and sometimes it is enough. The point at which it stops being sensible is when the symptom comes back, or when what you find behind the cover plate is not what you expected. That is the call we take most often, and it is the right time to make it.
We handle the full range of residential and commercial electrical work in Raleigh Hills: repairs and diagnostics, panel upgrades, wiring, outlets, lighting, and the dedicated circuits that keep a home running the way it should. Homes in this area were wired in different decades, and it shows in the panels. We are available every day from 8:00 AM to 10:00 PM.
Call (971) 366-2895 and we will scope the job before anything is scheduled.
A price is not a number we pull from a list. It is the result of understanding what the job actually involves. When you call, we ask about the symptom, the location, and what the circuit or panel looks like as far as you can tell. From that, we can usually give you a working figure before anyone arrives.
What moves a quote is what the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change. A simple outlet swap is a different job from an outlet swap that reveals aluminum wiring behind the box. A panel upgrade on a home with a clear service entrance is a different job from one where the meter base needs attention too. Those distinctions come out during the diagnostic, and we explain them before any work proceeds.
Pricing is explained on the call, confirmed before anything is scheduled, and revisited out loud if the scope changes on site. You get a straight answer when you ask what something costs. Call us and we'll walk you through the fix.
Attics, crawl spaces, and tall ceilings change how a job is planned, not just how long it takes. Running a new circuit through an unfinished attic is a different proposition from pulling wire through a finished space where every wall is closed. The access points matter, the insulation matters, and whether existing wiring is routed where the plans suggest it is matters too.
In older Raleigh Hills homes, crawl spaces often hold wiring that has been added to over the years with no clear documentation. A circuit that traces cleanly from the panel on paper may have junction points or splices that only show up once someone is underneath the house. We account for that when scoping the job, and we describe what we find before we proceed.
Tall ceilings come up most often with recessed lighting and ceiling fan installations. The work is not complicated, but the planning is different: load calculations, joist locations, and whether the existing switch leg can carry the new fixture all factor in. We confirm those details on the call so the visit does not turn into a discovery exercise. Before booking anything, the electrical services page is worth a read.
Electrical work done without a permit, or done by someone working outside their depth, shows up in a few consistent ways: wire nuts in a junction box that was never closed, a circuit that shares a neutral it should not, a breaker that is the wrong amperage for the wire it protects. None of that is unusual, and none of it requires tearing out everything that came before.
What we do is trace what is there, identify what is actually wrong, and explain the difference between a correction and a replacement. Some prior work can be brought into compliance with a relatively small fix. Some of it has to come out. We tell you which is which before we quote the repair, and we do not turn a code correction into a full rewiring project unless the wiring genuinely requires it.
Grounding and bonding are the most common gaps we find in homes that have had multiple rounds of electrical work. A circuit that was added without a proper ground, or a panel that was replaced without bonding the water pipe or the gas line, is a straightforward correction once it is identified. We handle those as part of the same visit when they come up during a diagnostic.
Commercial electrical work in a town this size tends to involve small retail spaces, professional offices, and light commercial properties that cannot simply close for a day while the electrical is sorted out. We plan around that from the start.
The first question on a commercial job is which circuits have to stay on and which can be isolated for the work. A retail space with a point-of-sale system, refrigeration, or security lighting has different constraints from an office suite that can run on a single live circuit while the rest of the panel is worked on. We scope that on the call and confirm it before the visit.
For businesses that cannot take any downtime during operating hours, we discuss what the schedule allows when you call. Work that needs the panel fully de-energized is better planned for a period when the space is not in use. We confirm what is available and what the job requires so the scheduling conversation is useful rather than vague.
A ceiling fan installation is more than a mounting job. The box in the ceiling has to be rated for a fan, the wiring has to include a proper switch leg, and the circuit has to carry the load without sharing too much with other fixtures. We confirm all of that before the fan goes up, and we replace the box if what is there is not rated for the weight.
Smart switches and dimmers require a neutral wire at the switch location, and older wiring in Raleigh Hills homes often does not have one. We assess the switch leg before quoting the installation. Where a neutral is not present, we explain the options.
An inspection is the right call before a home purchase, after storm damage, or when a property has older wiring that has not been looked at in years. We go through the panel, the visible wiring, the outlets, and the grounding, and we document what we find. If something needs attention, we explain it before any repair is scheduled.
A generator connected without a transfer switch is a hazard to anyone working on the grid outside your home. The transfer switch isolates the generator from the utility line and is a code requirement for any permanent hookup. We handle the circuit, the switch, and the connection to the panel. Pacific Northwest storm seasons and wildfire-related grid shutoffs make this a practical installation for many households in the region, not just a precaution.
Recessed lighting changes how a space reads, and the electrical side of that project involves more than cutting holes in the ceiling. Circuit capacity, joist locations, and the switch configuration all factor into the plan. LED retrofits for existing fixtures are a shorter job but follow the same process: confirm the circuit, confirm the load, and confirm the switch works with the new fixture type before anything is installed.
GFCI protection is a code requirement near water, and AFCI protection is required on most bedroom circuits in newer construction. Both show up as corrections during inspections of older homes that were wired before those requirements existed. We install them as standalone corrections or as part of a larger panel or wiring project, and we explain which locations require which type of protection.
When you call, you reach someone who knows the trade and can scope the job on the phone. The price is discussed before anything is scheduled. If the problem is urgent, describe what you are seeing and we will tell you what the schedule allows for that day. A sparking outlet, a panel that is warm to the touch, or a partial power loss affecting a significant part of the home are situations that need prompt attention, and we will tell you what can be arranged when you call.
For tenants or businesses that need to stay open during the work, we talk through what can be isolated and what has to stay live. That conversation happens on the scheduling call, not on the day of the visit. By the time we arrive, the scope is already agreed. Electrical service scheduled without the runaround is what that looks like in practice.
We take electrical work throughout Raleigh Hills and the surrounding communities in Washington County. That includes West Slope, Garden Home-Whitford, West Haven-Sylvan, Metzger, and Cedar Hills. If your property is in this part of the county, the process is the same: call, scope, price, schedule.
For residential and commercial electrical work alike, the call is where it starts. We do not require a form or an online submission. Pick up the phone and describe the situation.
Raleigh Hills has housing stock from multiple decades, which means we regularly encounter knob-and-tube wiring, aluminum branch wiring, and two-wire circuits without a ground alongside more recent work. Each type has its own requirements when it comes to repairs, additions, or code corrections. We identify what is there during the diagnostic and explain what it means for the job before anything is quoted.
We test the circuit or system that was repaired, confirm it is functioning correctly, and check that the fix has not affected anything adjacent. The panel is confirmed before we leave.
A buzzing panel often points to a loose connection, an overloaded breaker, or a breaker that is failing. It is not a sound to ignore. Call us and describe what you are hearing so we can assess the urgency.
Permit requirements depend on the scope of the work and, in some cases, whether the property is in a jurisdiction with specific rules about older wiring systems. We confirm what applies to your address before scheduling any work that is likely to require a permit. You do not need to research that yourself before calling.
We handle the permit process as part of the job. Requirements vary by location and by the scope of the work, and we confirm what applies before the job is scheduled.
A new addition needs circuits run from the panel to the new space, sized to the loads that will be in it. We assess whether the existing panel can carry the additional circuits or whether the panel needs to be upgraded as part of the addition.
A dryer runs on a dedicated 240-volt circuit with a specific outlet configuration and wire gauge sized to the appliance. A standard 120-volt outlet cannot power a dryer, and sharing a circuit with other loads is not acceptable for that draw.
Call (971) 366-2895 and tell us what you are dealing with.
We will scope the job, give you the price, and confirm what the visit covers. That is the whole process. We are available every day from 8:00 AM to 10:00 PM. Call Tigard Electrical Company and get the job on the calendar.
Have a look at our service map. We take electrical work in these nearby communities as well: Garden Home-Whitford, West Haven-Sylvan, Cedar Hills.
We cover the full range of residential and commercial electrical work in Raleigh Hills and across Washington County. The table below lays out what each service involves, who it fits best, and what is worth knowing before you call. Pricing is confirmed on the call before anything is scheduled, and every job is scoped clearly so you know what to expect.
| Service Type | What It Covers | Ideal For | Good to Know |
|---|---|---|---|
| Lighting Installation |
| Homeowners adding or upgrading interior or exterior lighting | We confirm the circuit can carry the added load before running any new wiring or mounting a fixture. |
| Electrical Panel & Service UpgradesMost Popular |
| Homes and commercial properties that have outgrown their current panel capacity or still have a fuse box | A load calculation is part of every panel upgrade so the new equipment is sized to what the property actually draws. |
| Electrical Safety Inspections |
| Buyers, sellers, landlords, and property managers who need a clear picture of wiring condition before a transaction or lease renewal | An inspection scopes what is there and what, if anything, needs attention. It does not commit you to any repair work. |
Call (971) 366-2895 to describe the job, get a rate, and schedule a visit. We are available every day from 8:00 AM to 10:00 PM.
(971) 366-2895